top of page
Writer's picturePRIMER GUN

SUPER GLUE CONTROLS (3g) - details


Very fast and powerful liquid super glue with direct-stop technology


TECHNOLOGY


PROPERTY


Direct-Stop Technology

Aspiration effect does not drop water drops.

Easy to use and clean

Very fast and powerful

Dishwasher Waterproof And Waterproof

APPLY


FITNESS:


Ideal for small area bonds (not suitable for large area bonds). Such as rigid PVC (polyvinyl chloride), such as adhesive almost all leather of plastic, ABS (acrylonitrile-butadiene-styrene, styrene impact resistance), PS (polysterene), acrylic resin (Plexiglas solid flexible material ® ), polycarbonate (Makrolon®), Phenolic Resin (Bakelite®), Porcelain, Ceramics, Wood, Metal, Cork, Felt, Cloth (Testability), Rubber.

Only partially suitable for glass (with time, the bond is brittle and weakens).



TRIM


BEFORE USING:


Working condition


Do not use at temperatures below + 10 ° C. The adhesive responds best to air humidity levels of 50-70%.


Personal safety


Cyanoacrylate adhesive cures very quickly when there is moisture (air humidity, skin moisture, sweat, skin sebum, tears). Therefore, care should be taken during use, especially with regard to contact with the skin and eyes with children. But even without treatment, cyanoacrylate adhesive dissolves naturally over time.


Surface requirements


The material to be glued should be clean, dry, free of dust and grease and fit well.


Preliminary surface treatment


Therefore, dirt, oil, grease, wax or separators must be completely removed from the surface and glued together. The best way to achieve this is to rub the parts several times with a suitable solvent such as acetone (if this is suitable for the material, check it first!).

For metals and metal alloys, it is usually enough to roughen the surface with emery paper or by grinding or brushing.

IN USE :


Packing handling


To drill the membrane, turn the entire cap tightly on the tube clockwise. Uncap and prepare to see the applicator!

Do not press on the tube during piercing.

How to use


Use a nozzle to apply the glue on the tube as thin as possible on one side (too much glue will slow down the curing process!) Press the parts together immediately. Depending on the amount and material of the glue, the glue is polymerized with synthetic resin within 60 seconds, connecting the two parts very strongly. When gluing in places with low humidity, breathing in one of the parts to be assembled can shorten the curing time. The best adhesion results are achieved at room temperature. The primary reaction surface accelerates the curing of the adhesive, and the new reaction surface (for example wood, ceramic, porcelain, leather) slows down the adhesion.

After use, clean the nozzle with a dry tissue and replace the cap to close the tube.

advice


If the skin clings, soak it in warm soapy water for as long as possible, and carefully separate it without force. After that, moisturize the skin.

Another possibility is to rub your fingers in warm water and push the clips or pieces of wire. After some time, you can detach your fingers. The affected area can also be treated immediately with acetone or nail polish remover. Since organic solvents remove grease, it is better to apply hand cream later. If glue stains remain, you can rub them using pumice. If the product is sprayed on eyes or mouth, it should be washed with plenty of water with the eyes or mouth open. See a doctor if necessary.

Because of the specific mes (fume) developed by cyanoacrylate adhesives, it is better to ventilate the premises well when using a relatively large amount.

Precautions


Attention: Super Glue contains cyanoacrylate. DANGER: Bonds skin and eyes in seconds Keep out of reach of children. May cause respiratory irritation. If medical advice is needed, prepare product containers or labels. Do not breathe vapor. If on eyes, rinse carefully with water for several minutes. If you have contact lenses, remove them easily. Continue rinsing.

AFTER USE :


Stain / Residue


Wipe off any excess glue immediately with a dry cloth. It is very difficult to remove the adhesive residue after curing. Acetone dissolves the adhesive, but dissolves very slowly (check for compatibility).


Storage conditions


Store in a dry, cool and frost-free place. Storage below +5 ° C (in the refrigerator) ensures maximum shelf life.



242 views0 comments

コメント


bottom of page